|

P0016 Ford F150: Meaning, Causes, Symptoms, And Solutions

You might have noticed your Ford F150 not having a smooth drive. In addition, the camshaft position sensors might not be providing the correct data at all times. Well, this problem usually corresponds to the P0016 code. So what exactly is the code P0016 Ford F150?

The P0016 code is a very common Diagnosis Trouble Code (DTYC). It usually corresponds to faulty values in the correlation of the camshaft and crankshaft positions. The code is triggered by the ECM as it finds these among the above sensors in the bank one position. 

So are you looking for a permanent fix to the problem? Well, you are in the right place to find out. All you need to do is scroll down and keep reading. 

What Does P0016 Code Mean On Ford F150?

The P0016 code has a very important role in every Ford vehicle. While it can occur in any model without exception, in this article, we will be talking about the F150 only. 

The Camshaft Position Sensor and Crankshaft Position Sensors correlate to each other in the task they do. For the engine to run smoothly, it must be in the right rotational phase at all times in the bank 1 intake.

However, there are times when they can act up without warning. If the ECM detects that these sensors are not in their accurate position at a specific time, it will trigger the code without fail. 

To get a short understanding of the meaning behind the code, you can look at the data we have gathered and pointed out below. 

  • P = Powertrain, the network or system of components that allow your car to move forward, provided that enough energy is produced. 
  • 0 = a generic number derived from the SAE standard 
  • 0 = It relates to the systems associated with the exhaust.
  • 16 = this is the problem-specific code index (Here, this can be defined as positional issues between the camshaft sensor and its corresponding crankshaft sensor.

Common Symptoms Of P0016 Code On Ford F150

If you have been using your Ford F150 for a long time, you must have received the P0016 code at least once. Along with this code, you must have also experienced one or more symptoms. 

Well, we have listed out some of these symptoms that most drivers have known to report the most. 

Rough car drivability

Since there is a lack of energy in the engine, driving the car will never be smooth and comfortable. In addition, it will be harder than normal to drive a car within a certain length.

Bad fuel economy

Low energy production means that the fuel economy of the vehicle’s engine will also be poor. This can be caused by poor engine performance and its mis-ability to conserve fuel.

Rattling chain noise

Stretched chains will be producing rattling sounds at all times when you drive the car. With so much sound in the background, it can be incredibly annoying for the driver as well as the passengers.

Takes a long time to start

Since there is a lack of energy and the sensors are out of commission, the engine might take a while before it can activate. Even when it is activated, it might not be the case where the wheels can turn.

It might not start at all

This is the worst-case scenario out of all of the symptoms mentioned here. Just like how we have mentioned the car starting after extended periods in the previous factor, they might also not start at all.

What Are Some Potential Causes Of the P0016 On Ford F150

Before you can look for the solutions, you must first understand the causes behind the P0016 code in your Ford F150.

There are several causes of the P0016 code in your Ford vehicle. While most of them might sound quite familiar, some can also be quite unheard of before here. 

  • Stretched or rusted chains
  • Faulty Sensors
  • Wrong or stale oil
  • Blocked valves

How To Diagnose And Fix P0016 Ford F150 Code?

If you are going to fix your Ford vehicle suffering from the P0016 code, you might need to take several steps.

The entire procedure has been compiled below in detail. You can take note of it as much as you want at your ease.

Diagnose Or Inspect The Engine

Before you can run any fixes on your Ford, you must first make some inspections.

Run a visual inspection first and then use an OBD-II scanner to make the stage even more effective. 

The diagnosis is meant to reveal what exactly the problem is causing the P0016 code to be triggered.  

Suppose you are negligible in the diagnosis stage; there are a lot of points that you can mix.

Even slight wear and tear might prove to be of crucial importance for countering the P016 code in your Ford F150. 

Stretched Or Rusted Chains

One of the most common reasons why the sensors might be out of rotational position is due to a malfunctioning chain. 

These chains can either be damaged, rusted, or even stretched. However, once damaged, the entire energy production in your engine will be affected in some way. It might even stop. 

You can use your power tools to bring the chain out and then oil it. Oiling the chain should bring it back to shape as this removes the rust layer on top of it. 

Replace The Sensors

The tasks that are associated with these problems are usually highly dependent on the data from the sensors. 

As a matter of fact, both the crankshaft and the camshaft are highly vital sensors used inside vehicles. 

If these sensors show a sign of a problem or even damage, replacing them with new ones might be the best choice for countering the issue. 

Since sensors tend to be non-serviceable components, there isn’t much you can do for repair. Do make sure to keep certain tools like screwdrivers and extra screws nearby since you might need them. 

Wrong Or Stale Oil

If you use a different type of oil than normal, the engine will definitely be affected. 

In addition, the same can also happen if you decide to use oil for an incredibly long period of time. This is because, as time passes, the viscosity of the oil changes. 

The Camshaft Position Sensor and Crankshaft Position sensors are already used for one oil type of certain viscosity. Therefore, using something else will disrupt their regular performance. 

Changing the oil at regular intervals and making use of the right oil type is the only way you can fix this problem.

In addition, make sure that you remove any traces of the old oil to prevent contamination. 

Blocked Valves

We have mentioned the usage of stale oil above. Another problem that is deeply imprinted by stale oil is the blockage of valves and pipes. This is caused by dried-up oil residues accumulating and blocking. 

The only way you can clean these blockages is by using a proper microfiber cloth and a cleaning solvent that is compatible with your Ford F150. 

Wipe down the solvents to ease the molecular attraction between the dried oil. This should remove the residues easily. If this doesn’t work, replacing the entire valve might be your only option. 

Go For A Test Drive

Once the fixes have been made, you can go for a test drive to check whether everything is okay or not.

Make sure that no more codes can get triggered and that ample energy is produced in the engines at all times.

How To Prevent Code P0016 On Ford F150 From Happening In The Future?

While there isn’t a lot you can do that speaks about a hundred percent guarantee on not triggering the code, certain precautions can still help you out. We have listed some of these precautions below. 

  • Check your engine oil and all times.
  • Apply lubricants to the metal components at regular intervals.
  • Compare sensor data to ensure that they are working properly
  • Check the voltage in the circuits against a reference voltage 
  • Never use the wrong oil type

Conclusion

If you have read through this article entirely, we expect that you must have already received the answer you came for. While we can’t help you all the way out, hopefully, our solutions can satisfy you. 

Of course, if you think you aren’t technical enough for the task, you can always hire a mechanic from outside to help you. However, even when you have hired the mechanic make sure to have enough knowledge on the fixes. 

Who knows what situations might come that could require you to fix your Ford F150 with the P0016 code. With the right technical knowledge, you can simply help yourself without spending any money at all. 

Related Posts:

Similar Posts

Leave a Reply

Your email address will not be published.